The driver suit blog – DGF2099-Main Page

The Driver Suit Blog Richard Petty Fan Suit

By David G. Firestone

When it comes to driver suits, I normally focus on race-worn items, but this week I’m going to shift gears, and focus on another kind of suit…and yes, pun intended. This example is a suit used by the Richard Petty Driving Experience. What the RPDE does is give die hard fans the ability to get in a stock car and either be driven around a track for a few laps, or drive the car around the track after some instruction. The cars are almost identical to Gen 4 cars, but have two seats and are scaled down to 600 horsepower from the over 800 currently run in NASCAR.

It looks similar in design to suits that Richard Petty wore during his racing days. Interestingly, there is no Petty blue, but a darker blue similar to the blue used in STP logos. There are no logos of any kind present, not even of the suit manufacturer, a company called Westex. I find it odd that at that time, the Richard Petty Driving Experience logo wasn’t used. There is no indication it was ever present on the suit to begin with. The legs are cuffed, as opposed to the boot cut that most NASCAR drivers like to use. Arm gussets, which give drivers better freedom of movement, are not here either. Later suits have some of these features.

Now even though the cars are either driven by professionals, or by drivers who have had lessons, the risk of crash and fire is present. As such, the fans are issued driver suits. This is an early version of the suit issued to them. What strikes me about this suit is that it is a single-layer suit with no epaulets. The epaulet is critical here because they are specifically designed for pulling an unconscious driver from a burning car in the event of a wreck. The fact that is is a single-layer suit is an issue here because in racing, redundancy is safety. NASCAR drivers wear double or triple-layer suits as well as fireproof long johns that give them 30 seconds of fire protection. I would be shocked if this suit would give 10 seconds.

I should also mention at this point that the suit does not have any SFI or FIA certification. When you are driving fans around a track with the ever present risk of fire, having a suit that can withstand the worst case scenario is a plus. SFI certification is designed to do just that, insure that the person wearing the suit will be able to be protected in the worst case scenario, so I do not get the logic of having uncertified suit for use.

All that said, now let’s discuss the basics.

The collar is a Velcro-shut design.

The tag is custom for the RPDE and has some things written and crossed out in Sharpie.

The sleeves are plain.

There is an unadorned belt.

The front torso shows some stains.

It should be noted that these suits are no longer used, and now Simpson SFI certified suits are currently in use. And while the suit has its short comings it is still a very attractive item. I plan on doing the RPDE in the very near future.

The Driver Suit Blog-PBR…Not the Beer, Power Boat Racing!

By David G. Firestone

Forest Barber is a true racer in every sense of the word. He won as a co-driver and owner in the 24 Hours of Daytona, along with one of my other favorite subjects Christian Fittipaldi. He has 5 other wins in the Grand Am Rolex Sports Car Series. He has also participated in motocross and enduro riding. He has had the most success in offshore powerboat racing, where he has 5 National and World championships. In 1999, he won the APBA National Championship as well as the Superboat International Championship while racing Drambuie on Ice. He wore this suit during that effort.

I never thought I would cover offshore powerboat racing in this blog, but this suit is a very interesting piece. It is a Sparco brand, single-layer suit that has full FIA certification. The light weight is used to accommodate the life jackets, and safety equipment that powerboat drivers need in addition to fire protection. Drowning is a real safety concern in power boat and other water sports. The front is designed with small DRAMBUIE ON ICE, TUBI STYLE EXHAUST SYSTEMS and KEITH EICKERT POWER PRODUCTS patches. Forest has signed the left chest and added WORLD CHAMPIONS 1999 as well. The back torso features a large DRAMBUIE ON ICE logo.

The sleeves both have a SPARCO logo, and one small patch. The right sleeve has a FEEL THE NEED RACING OFFSHORE CLASS 1 patch, and the left sleeve has a TNT CUSTOM RIGGING patch. There are no television logos, as the television coverage offshore powerboat racing had at the time did not have the cameras in the position for the logos to be seen.

Older Sparco suits have cowl tags indicating the size, and in this case, the size is 56, which is a large, with a 42 chest, 36 waist, and 42 hips. It also has two liability tags, one in the cowl and one behind the zipper in front.

The shoulders have no epaulets or any other design covering the seam. Epaulets as I’ve said before are designed to pull an unconscious driver from a burning car. In offshore powerboat racing, drowning is a big concern in addition to fire protection, so epaulets are not needed. The arms are gusseted.

There is an unadorned belt as well.

The legs are unadorned and are cuffed as opposed to boot cut.

This suit was worn in Class 1, which is considered by many to be the Formula 1 of powerboat racing. Two individuals race in the boat, one drives the boat while the other navigates. A track is set on an open body of water, and the boats race each other around that track. These boats have 850 horsepower engines and can reach speeds of 160 miles per hour. They are catamaran designs, having two hulls, which help not only with speed but with stability as well. The races are typically 55-75 nautical miles in length, over a course that is 11-15 laps long, often with one or two long laps.

This is the first powerboat racing suit I have ever seen, and I have to say, it’s a very nice piece.

The Driver Suit Blog-The Glossary of Terms

By David G. FirestoneFor this week’s blog, I will be doing a visual glossary of terms that I use when describing driver suits and helmets. To illustrate this, we will use this examples from a number of suits, including this Kasey Kahne suit from 2005.

and this Terry Labonte suit from 2008

Collar-The collar is the main protection for the driver’s neck. There are two types of collars, the ones that velcro shut, and the kind that overlap, but do not attach. A popular place for sponsor logos. Shoulder Epaulet-a piece of fabric used to decorate the shoulders. Some are designed for visual appearance, but some are designed to be used to pull an unconscious driver from a burning car. Another popular place for sponsor logos. Arm Gusset-Pieces of Nomex at the top of the sleeves that attach to the main body of the suit designed for driver comfort, while keeping it fire retardant. Liability Tag-Found in every piece of racing uniforms this tag states that any injury they incur while wearing the item is the fault of the driver, not the company. Series Logo-Logo indicating what series the driver is racing in. Currently found at the top of the suit on the right side for NASCAR and the left side for IndyCar, though it has been more nomadic in the past. Associate Sponsor Logos-Smaller logos found at the top of the chest. Typically these include the series logo, tire logo, car manufacturer, team name, and one or two other sponsors. These small logos are a good way to photomatch a suit. Primary Sponsor Logo-The biggest logo on the suit, can measure as much as 14 inches around. Usually found on the center torso on front and upper torso on back. This logo is also the reason is why all of the other design features of the suit revolve around. Belt-Many driver suits feature a belt, which is for driver comfort. The safety certification is sometimes found on the inside, has a velcro closure. The driver name or a sponsor logo is often found here. Television Logo-Found on the sleeves and legs, these logos are specifically positioned so that when the driver is sitting in the car, they appear visible to the in-car cameras. Cuff-the end of the arms and legs have a Nomex cuff. On the legs, the cuffs are often covered by a boot cut. Double or Triple-Layer-Most driver suits have multiple layers of Nomex in them to protect the driver from firescreen

Safety Certification-Driver suits are independently inspected by FIA and/or SFI to insure that they meet or exceed the fire protection they promise to provide. SFI certification is typically found on the inside of the left sleeve, and FIA can be found on either the back of the neck, or inside the belt.

The Driver Suit Blog..The SFI and FIA patches…Why they are as critical as they are.

By David Firestone

Many race fans have seen these small patches on driver suits, and may have wondered what they are. What many do not realize is that these small patches have a very critical role in driver safety. These small patches are the safety certification patches. These small patches state that this uniform part has been examined by one of the two groups, and determined to meet the standards set by the group. For North American made equipment that group is SFI.

According to their website, SFI was founded in 1963 as part of Speed Equipment Manufacturers Association or SEMA, as a safety group. Back then, the safety culture wasn’t as rigorous as it is today, and there were not many standards in place. SEMA started the safety certification with SFI or SEMA Foundation, Inc certification. If the equipment didn’t meet SFI standards, the participant could be denied entrance to the event. Eventually, SFI left SEMA and became its own independent group.

Since then, SFI has certified safety equipment, and their certification is the standard in North America. This small patch is usually sewn into the inside wrist area on the left sleeve. This example, from a Terry Labonte suit from 2008, indicates that the suit meets “3.2A/5” standards. According to their site, this certification is standard for driver suits, and this suit would need re-certification in the next 5 years, or 2013. This certification is standard for many NASCAR suits, as shown below.

For suits made internationally, the certification comes from a different group, the FIA Institute. Like SFI, the FIA Institute has the exact same goal, to make sure auto racing is safe, and that the equipment that drivers wear is as safe as possible. Unlike SFI however, FIA certification ends up in one of two places, either on the back of the neck,or inside the belt,

Both certifications serve the same purpose and both are mandated in racing today. These certifications also appear on driver gloves,and even helmets, usually on the HANS anchorMoving on to more 2013 paint schemes…

Trevor Bayne #6 Valvoline Ford Mustang Love this scheme! This brings back some fond memories of Mark Martin behind the wheel back in the 1990’s. The color and design scheme are amazing, so it gets an A

Regan Smith #7 Tax Slayer/Hellman’s Chevy Camaro Same as the 5 and 88, so nothing really to say here…

Brad Keselowski #22 Hertz Ford Mustang Only Penske can ruin one of the best color schemes with an awful design. Seriously what is the design on the front? It kills this scheme. Final Grade: D

Travis Pastrana #60 Ford Mustang What the Hell? Did Lisa Frank design this car? I’d love to comment on the color scheme, but just looking at the picture is enough! I didn’t think it was possible to make a scheme worse than the Kyle Bush Sponsafier car, but here we are! Final Grade: F’

By the way, I never thought I would reference Lisa Frank in this blog…

Jamie McMurray #1 Cessna Chevy SS Cessna has figured out the way to a good paint scheme, simple colors and simple design. It works very well and earns an A grade.

Casey Mears #13 Geico Ford Fusion Eww…just eww. The color scheme is dreadfull, and the designs on the side are painful to look at. It passed because of the logo and number design. Final Grade: D-

Kyle Busch #18 Interstate Batteries Toyota Camry Great color scheme, and good basic design, but there is something with this car I find annoying. The driver’s name is on the windshield and above the door, so why is it on the top of the hood? Not just on the top of the hood, but UPSIDE DOWN as well? Seriously? It makes no sense, and takes the final grade down to a B

The Driver Suit Blog-NASCAR Helmets Over The Years

By David G. FirestoneThe evolution of the racing helmet in NASCAR for the most part was slow, in the beginning. NASCAR was officially founded in 1947, two years after World War II ended. Many of the helmets worn during the 1940’s and 1950’s were little more than repainted army and air force helmets. These helmets were basic at best, and as protection for the dangers of racing, these helmets were inadequate at best. During the 1950’s, many drivers switched from military headgear to motorcycle helmets. In the 1960’s, motorcycle-style helmets became the norm.The above helmet was worn by Jim McConnell, who raced and promoted races in Maine, and went on to found Beech Ridge Motor Speedway in Scarborough, Maine. This is a racing helmet, but it looks more like Wyatt’s Captain America helmet from Easy Rider, in its basic design. It has an open face, no microphone equipment, and is rather thin. Although there would be advancements in helmet technology, the open-face design would remain popular until the 1980’s.This helmet was worn by Brad Noffsinger in 1988, it is the same general design, though it is much thicker, has some advancements in visor technology, and had some microphone technology in it as well. Although these helmets have since been banned, they remained legal for as long as they did for one simple reason: Advanced visibility. NASCAR did not want to have a crash caused by decreased visibility due to a rule mandating full-face helmets.The Ted Musgrave helmet mentioned in a previous post is a perfect example. The bottom part covering the chin does to a certain extent reduce visibility for a driver. The logic makes sense, in that if there was a crash caused by reduced visibility, so for the 1990’s and 2000, the open-face was legal…then came the 2001 Daytona 500. That race saw the death of Dale Earnhardt Sr. from a Basilar skull fracture, which as tragic as it was, wasn’t the first death due to sub-par safety equipment. John Nemechek, Adam Petty, Kenny Irwin Jr., and Tony Roper had all been killed in similar accidents. Only after Earnhardt’s death, did the HANS device come to light, and eventually became mandatory in NASCAR, and eventually, across the board in racing. Now the helmets used in NASCAR look like this:This is a helmet worn between 2004 and 2005 by either Regan Smith or Jason Keller. As you can see, it has a number of advancements, including the visor, and air intakes, but the biggest advancement is these small bolts towards the back.These are where the HANS device connects to the helmet. The HANS device was mandated after the death of Dale Earnhardt Sr. to prevent Basilar skull fracture deaths. This device has worked very well. The HANS device works by attaching the device to the helmet, and then being secured by the shoulder straps.

As advanced as this helmet is, there is always room for improvement. What new form will the racing helmet of tomorrow take? Only time will tell.

On to Paint Schemes, we have a lot of ground to cover today…

First in the Camping World Truck Series

Chris Cockrum #07 Accu-Tech/Homesmart Toyota Tundra Decent color scheme, good stripe pattern, logos are easy to see. Solid A grade.

Sean Coor #82 Warriors in the Workplace Ford F-Series Simple yet bold. Great use of matte black, great number design and color scheme. The logo is easy to see and stands out. No distracting stripes or patterns. Solid A grade.

Next up, the Nationwide Series

Sam Hornish Jr. #12 Wurth Tools Ford Mustang The doors look like they have race damage on them already, which is not a good sign. The color scheme is decent, but the Pennzoil stripes just kill it. The logos are easy to see, but the stripes are just awful. Final grade C+

Matt Kenseth #18 Reser’s Foods Toyota Camry. Numbers are great, color scheme is good, logos are easy to see, and the background design is visible, but not overpowering. The only thing keeping this scheme from a higher grade is the picture of the package on the side of the car. That drags the grade down to a B+ from an A

Now moving on to the Sprint Cup Series

Denny Hamlin #11 FedEx Toyota Camry There are a total of 4 variations of the FedEx scheme, Express, Freight, Ground and Office. Right off the bat, the front nose design and stripes are awful. The color schemes are great, as are the logos and numbers, but the stripes kill it. The best grade I can give is a C+ across the board.

Paul Menard #27 Menard’s Chevy SS Not the worst I have ever seen, but the yellow is way too bright, and the massive collection of sponsor stickers on the quarter panel is just ugly. Final Grade C-